Key Product Information

Flexible Operation​

The EMGen EMC Signal Generator can be used in Continuous Wave (CW) mode, as well as AM or pulse modulation mode.
The EMGen covers a frequency range from 9 kHz to 6 GHz and can be used for both conducted and radiated immunity tests. It has two SMA output connectors; one for low frequency output (LF) and one for high frequency output (HF).
The LF output covers the signal generator from 9 kHz to 230 MHz. It is intended for conducted immunity set-ups, like the IEC61000-4-6 or ISO11452-4 (BCI).
The HF output covers the signal generator from 80 MHz to 6 GHz and therefore can be used for radiated immunity tests like the IEC61000-4-3 and ISO11452-2 (ALSE).

Accurate Measurements

The EMGen is an accurate RF signal generator with a frequency error of less than 20 ppm and a modulation accuracy better than 2%. At the same time its output has an extremely fast response (less then 500μs) which is very important for EMC testing.
In addition, special engineering efforts have been taken to assure complete monotone behavior and prevent undesirable results at the output level. All these features make the EMGen the perfect signal generator for EMC immunity testing.

Easy to Use

The EMGen system is “Plug-and-Play”, meaning this card is automatically recognized and initialized by the EMCenter and is immediately ready to use. The user can configure and control the system by using TILE!™ Lab Management Software.​

Specifications Select a tab below for more information

7003-001 Plug-in Card Feature
​​Frequency Band
​9 kHz to 230 MHz (LF Output)
80 MHz to 6 GHz (HF Output)​
​Frequency Resolution​
​1 Hz
​​​Frequency Error​
​+/- 20 ppm
​​Minimum Output Level
​​-70 dBm​
​Maximum Output Level​
​+10 dBm (+4.0 dBm When Using AM)​
​Amplitude Resolution
​​0.1 dBm
​​Amplitude Accuracy
​​+/- 1.5 dB​
​Output Level Settling Time​
​<500 us
​<- 50 dBc
​​​Non-Harmonic Spurious​
​<- 50 dBc​​
​Modulation Types​
​CW, AM and Pulse​​
​Modulation Frequency Range
​​10 Hz to 100 kHz​
​AM Modulation Depth
​​5 to 95% (Usable 0 to 100%)​
​AM Accuracy, Output LF
Measured at 0 dBm Level​
​< +/- 3% (5 to 95% Modulation Depth)​
​AM Accuracy, Output HF
Measured at 0 dBm Level​
​< +/- 2% (10% to 90% Modulation Depth)
< +/- 3% (5 to 10% and 90 to 95% Modulation Depth)
​​Pulse On/Off Time Range​
​200 ns to 100 s​
​Pulse Modulation On/Off Ratio
Output LF
​​> 60 dB (9 kHz to 230 MHz)​
​Pulse Modulation On/Off Ratio Output HF
​​> 90 dB (80 MHz to 1 GHz)
> 70 dB (1 GHz to 3 GHz)
> 60 dB (3 GHz to 6 GHz)​
12 VDC​
Dimensions: 3U x One 19 in Slot in EMCenter
Temperature Range (Use): +10° C to +40° C
Relative Humidity: 10 to 90% (Non-condensing)



EMCenter™ Modular RF Platform Model 7000 Series​​ETS-Lindgren's EMCenter™ is a modular RF platform consisting of an integrated micro-controller, modular chassis, and a selection of optional plug-in card modules. It can be used to perform a variety of RF measurement applications.
EMControl™ Positioner Controller Plug-in Card Model 7006-01 ​ETS-Lindgren's EMControl™ is a versatile positioner controller which enables the user to synchronize simultaneous movement of two ETS-Lindgren positioning devices (for example, towers or turntables) and On/Off operation of an additional auxiliary device (LISN, EUT, etc.).<br>
EMGen™ RF Signal Generator Model 7003-001 ​​​​​ETS-Lindgren’s EMGen™ RF Signal Generator Plug-in Card offers users a convenient and economical solution for signal generation.
EMPower™ Power Meters Model 7002-006 ETS-Lindgren has extended its range of EMPower RF power meters to comply with the measurement requirements of the ETSI 300 328 and 301 893 standards for wideband data transmission systems, including IEEE 802.11™, Bluetooth® and Zigbee™. 
EMPower™ Power Meters Model 7002-00X ​​ETS-Lindgren's EMPower™ Power Meters make fast, accurate power measurements, even at low power levels.
EMPower™ Pulse RF/Burst Power Meter Model 7002-00X ETS-Lindgren's EMPower Pulse RF/Burst Power Meter is designed to perform very fast measurements on high-frequency pulse-shaped signals (RF bursts).
EMSense™ EMF Probe Plug-in Card Model 7007-001 ​ETS-Lindgren EMSense™ EMF Probe Plug-in Card provides an interface for ETS-Lindgren’s battery-powered E-field probes to the EMCenter Modular RF Platform.
EMSense™ EMF Probe Plug-in Card Model 7007-002<p>​​ETS-Lindgren EMSense™ EMF Probe Plug-in Card provides an interface for ETS-Lindgren’s laser-powered E-field probes to the EMCenter Modular RF Platform.</p>
EMSwitch™ RF Switch Plug-in Cards 7001-00X ​​ETS-Lindgren's EMSwitch™ RF Switch Plug-in Cards are general purpose multi-channel switch matrixes, used to switch the RF path of equipment for RF measurement applications, including immunity, emissions, and wireless measurements.

Key Features

  • Easy to Use
  • Flexible LF and HF Operation
  • Accurate Measurements for EMC Test

Literature and Videos<a href="/sites/etsauthor/ProductBrochures/General%20Brochures/Test_and_Measurement_Full_Line.pdf"><img alt="" src="/_layouts/15/IMAGES/icpdf.png" />Test_and_Measurement_Full_Line.pdf</a>

L o a d i n g

 Catalog-Item Reuse